29 Feb memorandum contains management control pro- visions in accordance with AR but does not identify key management controls that must. KEY CONTROL REGISTER AND INVENTORY. For use of this form see AR 11; the proponent agency is PMG. PERIOD COVERED. FROM: TO: DA FORM. 1 Apr AR , Physical Security of Arms, Ammunition and Explosives (15 PURPOSE: To establish an integrated key and lock control system for.

Author: Zulkilabar Zolozil
Country: Canada
Language: English (Spanish)
Genre: History
Published (Last): 13 November 2015
Pages: 355
PDF File Size: 5.21 Mb
ePub File Size: 4.73 Mb
ISBN: 998-3-28730-508-3
Downloads: 55291
Price: Free* [*Free Regsitration Required]
Uploader: Taran

Sign In Sign Out. Lock and Key Systems Af are the most acceptable and widely used security devices for protecting facilities, classified materials, and property.

Since the lock body and the strike are interconnected with locking pins when closed, the lock essentially becomes a single unit and is extremely difficult to separate. The locking cylinder located in the ar 190-11 key control of the doorknob distinguishes these locks. They are mounted on the door in a manner similar to cylindrical locksets. Refer to ARAppendix D, for standard key 1900-11 ar 190-11 key control procedures.

AR prescribes standard facilities for storing classified material and contains guidance for different storage requirements. Some cylindrical locksets have keyways in each of the opposing knobs that require a key on either side to lock and unlock them. It is recommended for use in military housing as an effective security measure in the installation’s ar 190-11 key control program. The brass or bronze locks are commonly used but do not meet the security requirements of the hardened shackled locks.

A lock can and will be defeated. These locks are a complete, one-piece unit that slides into a notch cut into the door’s latch edge. Locks are keyed in several different ways.

Locks are the most acceptable and widely ar 190-11 key control security devices for protecting facilities, classified ar 190-11 key control, and property. In situations where contgol is a window in or adjacent to the door, a double-cylinder dead-bolt lock one that requires a key to open from either side should be used.


key control army regulation – – Content Results

When the bolt is extended lockedthe dead bolt projects into the doorframe at least one inch, and ar 190-11 key control cannot be forced back unlocked by applying pressure to the end of the bolt. Although the lock is the most accepted and widely used security device, it is only a delay device and should never be considered as a positive bar to entry.

ARs,and prescribe specific types of locks for specific types of facilities. Others unlock with a key, but may be locked by pushing or rotating a button on the inside knob.

Types of Locking Devices Enter Your Ar 190-11 key control Address. Some locks have interchangeable cores, which allow the same key system to include a variety of locks. The primary difference is in the bolt.

Mechanical, push-button combination locks are digital push buttons numbered 1 through 9 combination door-locking devices used to deny area access to any individual not authorized or cleared for a specific area.

Dead-bolt locks are sometimes called tubular dead bolts.

Key locks consist of, but are not limited to, the following: Mortise locks are so named because the lock case is mortised or recessed into the edge of the door. Physical-security personnel must work closely with engineer personnel to ensure that locks meet the standards and are installed according to ar 190-11 key control regulations. Combination locks may be either mechanical or electronic. Master-keying is not used unless permitted by regulation.

Locking devices cotrol listed in TM The ar 190-11 key control kwy can be locked from inside by means of a thumb turn or by a button.

Ar 190-11 key control and Maintenance Entrance doors often have an exterior thumb latch rather than a doorknob. Key locks consist of, but are not limited to, the following:. When closed, locking pins in the lock body drop down into the 190-1 provided in the strike and secure the locking system. Master-keying is done for convenience and represents the controlled loss of security.


These locks are suitable only for very low-security applications. Web Search

Mortise locks are considered low-security devices ar 190-11 key control they weaken the door in the mortised area. Padlocks are detachable locks that are typically used with a hasp. When several locks are keyed differently, each is operated by its own key. The degree of protection afforded by ar 190-11 key control vault, a safe, or a filing cabinet may be measured in terms of the lock’s ar 190-11 key control.

Low-security padlocks, sometimes called secondary padlocks, are used to deter unauthorized access, and they provide only minimal resistance to force. They provide the maximum resistance to unauthorized entry when used with a high-security hasp.

The tailpiece screws are usually scored so that the lock can be tailored to fit varying door thicknesses. Unit locks are ideal in heavily traveled facilities such as hospitals or institutional buildings. They are operated by entering a particular sequence of numbers. Both the drop-bolt lock body and the strike have interlocking leaves similar to a door hinge.

Regardless of their quality or cost, locks are considered delay devices only. Cylindrical locksets are often called key-in-knob or key-in-lever locks. The one-size cutout of the door edge simplifies the door preparation for the lock.

These locks are generally used with drop-bolt and other surface-mounted locks and latches. Installation-level ar 190-11 key control are responsible for maintaining the locking devices. They consist of an outer barrel, a cylinder and ring, a tailpiece, a back mounting plate, and two mounting screws. Ar 190-11 key control the correct combination is entered, the lock’s bolt is retracted. Precautions must be taken to avoid confusing these locks with similar brass or bronze locks.

Rim-cylinder locks are mounted to the door’s inside surface and are secured by screws in the door face.